This is a companion discussion topic for the original entry at https://blogs.rstudio.com/tensorflow/posts/2020-10-09-torch-optim
This is the fourth and last installment in a series introducing torch basics. Initially, we focused on tensors . To illustrate their power, we coded a complete (if toy-size) neural network from scratch. We didn’t make use of any of torch ’s higher-level capabilities – not even autograd , its automatic-differentiation feature.
This changed in the follow-up post. No more thinking about derivatives and the chain rule; a single call to backward() did it all.
In the third post, the code again saw a major simplification. Instead of tediously assembling a DAG 1 by hand, we let modules take care of the logic.
Based on that last state, there are just two more things to do. For one, we still compute the loss by hand. And secondly, even though we get the gradients all nicely computed from autograd , we still loop over the model’s parameters, updating them all ourselves. You won’t be surprised to hear that none of this is necessary.
Losses and loss functions
torch comes with all the usual loss functions, such as mean squared error, cross entropy, Kullback-Leibler divergence, and the like. In general, there are two usage modes.
Take the example of calculating mean squared error. One way is to call nnf_mse_loss() directly on the prediction and ground truth tensors. For example:
x <- torch_randn(c(3, 2, 3))
y <- torch_zeros(c(3, 2, 3))
nnf_mse_loss(x, y)
torch_tensor
0.682362
[ CPUFloatType{} ]
Other loss functions designed to be called directly start with nnf_ as well: nnf_binary_cross_entropy() , nnf_nll_loss() , nnf_kl_div() … and so on. 2
The second way is to define the algorithm in advance and call it at some later time. Here, respective constructors all start with nn_ and end in _loss . For example: nn_bce_loss() , nn_nll_loss(), nn_kl_div_loss() … 3
loss <- nn_mse_loss()
loss(x, y)
torch_tensor
0.682362
[ CPUFloatType{} ]
This method may be preferable when one and the same algorithm should be applied to more than one pair of tensors.
Optimizers
So far, we’ve been updating model parameters following a simple strategy: The gradients told us which direction on the loss curve was downward; the learning rate told us how big of a step to take. What we did was a straightforward implementation of gradient descent .
However, optimization algorithms used in deep learning get a lot more sophisticated than that. Below, we’ll see how to replace our manual updates using optim_adam() , torch ’s implementation of the Adam algorithm (Kingma and Ba 2017). First though, let’s take a quick look at how torch optimizers work.
Here is a very simple network, consisting of just one linear layer, to be called on a single data point.
data <- torch_randn(1, 3)
model <- nn_linear(3, 1)
model$parameters
$weight
torch_tensor
-0.0385 0.1412 -0.5436
[ CPUFloatType{1,3} ]
$bias
torch_tensor
-0.1950
[ CPUFloatType{1} ]
When we create an optimizer, we tell it what parameters it is supposed to work on.
optimizer <- optim_adam(model$parameters, lr = 0.01)
optimizer
<optim_adam>
Inherits from: <torch_Optimizer>
Public:
add_param_group: function (param_group)
clone: function (deep = FALSE)
defaults: list
initialize: function (params, lr = 0.001, betas = c(0.9, 0.999), eps = 1e-08,
param_groups: list
state: list
step: function (closure = NULL)
zero_grad: function ()
At any time, we can inspect those parameters:
optimizer$param_groups[[1]]$params
$weight
torch_tensor
-0.0385 0.1412 -0.5436
[ CPUFloatType{1,3} ]
$bias
torch_tensor
-0.1950
[ CPUFloatType{1} ]
Now we perform the forward and backward passes. The backward pass calculates the gradients, but does not update the parameters, as we can see both from the model and the optimizer objects:
out <- model(data)
out$backward()
optimizer$param_groups[[1]]$params
model$parameters
$weight
torch_tensor
-0.0385 0.1412 -0.5436
[ CPUFloatType{1,3} ]
$bias
torch_tensor
-0.1950
[ CPUFloatType{1} ]
$weight
torch_tensor
-0.0385 0.1412 -0.5436
[ CPUFloatType{1,3} ]
$bias
torch_tensor
-0.1950
[ CPUFloatType{1} ]
Calling step() on the optimizer actually performs the updates. Again, let’s check that both model and optimizer now hold the updated values:
optimizer$step()
optimizer$param_groups[[1]]$params
model$parameters
NULL
$weight
torch_tensor
-0.0285 0.1312 -0.5536
[ CPUFloatType{1,3} ]
$bias
torch_tensor
-0.2050
[ CPUFloatType{1} ]
$weight
torch_tensor
-0.0285 0.1312 -0.5536
[ CPUFloatType{1,3} ]
$bias
torch_tensor
-0.2050
[ CPUFloatType{1} ]
If we perform optimization in a loop, we need to make sure to call optimizer$zero_grad() on every step, as otherwise gradients would be accumulated. You can see this in our final version of the network.
Simple network: final version
library(torch)
### generate training data -----------------------------------------------------
# input dimensionality (number of input features)
d_in <- 3
# output dimensionality (number of predicted features)
d_out <- 1
# number of observations in training set
n <- 100
# create random data
x <- torch_randn(n, d_in)
y <- x[, 1, NULL] * 0.2 - x[, 2, NULL] * 1.3 - x[, 3, NULL] * 0.5 + torch_randn(n, 1)
### define the network ---------------------------------------------------------
# dimensionality of hidden layer
d_hidden <- 32
model <- nn_sequential(
nn_linear(d_in, d_hidden),
nn_relu(),
nn_linear(d_hidden, d_out)
)
### network parameters ---------------------------------------------------------
# for adam, need to choose a much higher learning rate in this problem
learning_rate <- 0.08
optimizer <- optim_adam(model$parameters, lr = learning_rate)
### training loop --------------------------------------------------------------
for (t in 1:200) {
### -------- Forward pass --------
y_pred <- model(x)
### -------- compute loss --------
loss <- nnf_mse_loss(y_pred, y, reduction = "sum")
if (t %% 10 == 0)
cat("Epoch: ", t, " Loss: ", loss$item(), "\n")
### -------- Backpropagation --------
# Still need to zero out the gradients before the backward pass, only this time,
# on the optimizer object
optimizer$zero_grad()
# gradients are still computed on the loss tensor (no change here)
loss$backward()
### -------- Update weights --------
# use the optimizer to update model parameters
optimizer$step()
}
And that’s it! We’ve seen all the major actors on stage: tensors, autograd , modules, loss functions, and optimizers. In future posts, we’ll explore how to use torch for standard deep learning tasks involving images, text, tabular data, and more. Thanks for reading!